6 Ways to Fix Apple Watch Won't Turn on

You wake up one morning and try to switch on your Apple Watch, but it will not turn on. "Why my Apple watch won't turn on?" you'll naturally question. This is not a typical problem with this kind of gadget. It might imply a million things if your Watch refuses to turn on. Fortunately, there's no need to fear because there are a few simple solutions to work around the problem and fix it on your Apple iPhone. You'll learn what's causing your Apple Watch to not switch on in the following guide.

Part 1: The Reason for Apple Watch Not Turning on

Your Apple Watch may not turn on for a variety of reasons. Here are some of the possible causes of problems with your Watch's boot-up.

Battery Is Dead

You may have been using your Apple Watch without charging it for a long time, and the battery is completely depleted and now the Apple Watch won't turn on or charge. Your Watch simply does not have enough energy to switch on and power up the functionalities in this scenario. This is frequently the cause of Apple Watches not turning on.

A Software Problem

Another possibility is that your Apple Watch has a software issue that prevents it from running the upgrade. When this happens, your Watch is unable to load the firmware and will not turn on.

Damage to the Charging Cable

Finally, there could be a problem with the charging cable for your Apple Watch. Perhaps the cable is broken or damaged, and it is unable to transmit adequate power to the Watch. You may believe your Apple Watch is charging in this case, but it is not.

Part 2: Apple Watch Won't Turn on? Fix It on Apple Watch

Way 1: Charge Apple Watch and Check the Charging Cable

The fact that your Apple Watch is out of battery is one of the most common reasons Apple watch won't turn on. The simple remedy in this instance is to plug your Watch into a charging port. Get a cable and connect it to both your Apple Watch and a charging socket, then wait a few minutes for your Watch to charge. You'll have to wait a little longer for your gadget to power up if the battery is entirely depleted.

Check the charging cable to make sure it isn't damaged or broken if your Watch still won't switch on after a time. To charge your Apple Watch, it must be in working order. If the cable is defective, have it replaced right away with an Apple original cable.

fully charge the watch

Way 2: Force Restart Apple Watch

When your Apple Watch won't turn on, you can also conduct a hard reset. Press and hold the Digital Crown and the Side button at the same time for roughly 10-15 seconds. Release both buttons when the Apple logo shows on your Apple Watch. Shortly after, your Apple Watch will switch back on.

Here's why the hard reset cured your Apple Watch: its software crashed, rendering the display black. Your Apple Watch was on the whole time!

hard reset the phone

Note: You may need to keep both buttons down for up to 20 seconds!

Way 3: Turn off Power Reserve

When someone buys their first Apple Watch, they may accidentally put it in Power Reserve mode and believe it isn't working. I remember playing around with this function on my Apple Watch when I initially received it and thinking the same thing that how do I fix my Apple Watch that won't turn on?

Power Reserve is a feature that extends the battery life of your Apple Watch by turning off all of its other capabilities except the current time. If it looks like the image below, you have Power Reserve turned on:

Press and hold the Side button until the Apple logo appears on the screen if your Apple Watch is in Power Reserve mode. Your Apple Watch will no longer be in Power Reserve mode when it reboots.

Turn off power reserve

Part 3: Apple Watch Won’t Turn on? Fix It on iPhone

Way 1: Disable Voiceover and Screen Curtain on iPhone

Screen Curtain, an accessibility feature on the Apple Watch, may also be used to turn off the display. This tool is part of the VoiceOver visual impairment help. When VoiceOver is enabled, the watch is controlled by sound instead of sight.

If you've tried a hard restart, charging your phone, and inspecting the charging station without success, make sure VoiceOver is turned off in the Apple Watch settings. This does not necessitate the use of a watch.

1.From the iPhone that you paired with the Apple Watch, open the Watch app.

2.If you aren't already on the My Watch screen, tap My Watch at the bottom.

3.Select Accessibility from the drop-down menu.

4.Toggle the slider next to VoiceOver to turn it off.

5.If it says "On" next to VoiceOver, tap it.

6.Toggle the slider next to VoiceOver to turn it off.

Fix by connecting with phone

Way 2: Erase Apple Watch and Pair It on iPhone

If your Apple Watch won't turn on series 3, you might be wondering why you should wipe it. The reason for this is that it is regarded as a one-stop solution. Plus, there's more. It has a knack for resolving even the most difficult problems. So, if your Apple Watch won't turn on, try this unconventional yet effective troubleshooting method.

1.On your iPhone, go to the Watch app > General. Scroll down towards the bottom to find the reset button.

2.Next, select Erase All Content and Settings from the menu.

3.Connect your Apple Watch to your iPhone after you've successfully wiped it.

4.If your Watch was not responding or the display was dead due to a software fault, you can usually fix it by resetting it and your Watch will return to the setup screen, ready to be linked with your phone.

Erase and pair with phone

Way 3: Fix the iPhone That Matches to Apple Watch

The Apple Watch isn't the only Apple product that won't turn on. This problem could potentially affect your iPhone or iPad, so it's crucial to know how to deal with it if it happens.

Fortunately, UltFone iOS system repair is an app that can help you fix nearly all difficulties with your iOS-based devices. There's a feature called system repair that digs deep into your device's system and fixes it from the ground up. Is your iPhone's screen frozen and refusing to turn on or Apple Watch won't turn on after hard reset? UltFone iOS system repair program can fix 150+ iOS system issues, including Apple logo stuck, blank screen, restart loop, recovery mode, and even factory reset iPhone/iPad without password.


  • On an iPhone, iPad, or iPod, simply click once to enter and exit recovery mode.
  • Repair more than 150 iOS system issues such as the reboot loop, Apple logo, and blank screen without losing data.
  • Reset iPhone/iPad/iPod Touch/iTunes/Finder if you don't have a password.
  • All iPhone models and iOS versions are supported, including the current iPhone 13 series and iOS 15, and you can downgrade from iOS 15 to iOS 14 without using iTunes.
Free Download For PC Secure Download Free Download For Mac Secure Download


You can easily cure these iOS system issues using UltFone iOS 15/14 System Repair in just a few clicks without losing any data. Let's take a deeper look at how it currently works!

  • Step 1 Download and Launch UltFone iOS System Repair

    Connect your iPhone/iPad/iPod to your computer after downloading and running this application on your PC/Mac. Click "Start" to begin the iOS framework fix module.

    download and launch ultfone

  • Step 2 Select Standard Repair

    1. On the following screen, choose "Standard Repair" to continue.

    2. The two repair options accessible, as visible on the interface, are Standard Repair and Deep Repair. The primary difference is that Standard Repair may solve any iOS bugs without destroying any data.

    3.The Deep Repair mode, on the other hand, will wipe your device clean and assist you in resolving more significant iOS issues that the Standard Repair option failed to resolve. Select Deep Repair if the Standard Repair option does not solve your problem or if you wish to factory reset your iPhone/iPad without a password.

    Select standard or deep repair

  • Step 3 Download Firmware Package

    1. To acquire the automatically matched firmware package for your device, choose the "Download" option before beginning the system repair. By choosing "Browse" and selecting a different location to save the firmware package, you may modify the default path.

    2. To import your firmware package, click "import local firmware" if you have previously downloaded the firmware.

    3. Please be patient, as the firmware package is around 2.5 GB in size, and keep the area clean.

    download firmware package

  • Step 4 Start Repairing Operating System

    1. To fix the iOS problems on your smartphone, click "Start Standard Repair" when the firmware package has been successfully downloaded.

    2. Wait for the iOS system to be fixed, which should just take a few moments.

    repair ios system

  • Step 5 Complete the iOS System Repair

    Your iOS device will reboot and everything will be back to normal when the iOS system recovery is completed.

    standard repair completed


There are various reasons why your Apple Watch won't turn on. The tutorial above will assist you in identifying these causes and describing how to resolve the issue on your Watch. Regardless, UltFone iOS System Repair is the greatest option accessible. One of the techniques will fix the problem, and your Apple Watch will switch on without any additional issues.